Aluminium

Coil

Aluminium
Coils

The easily exchangeable test pipeline of these Aluminium 6082 Coils is filled with the sample and cooled down to a set temperature. In general, wear resistance can be improved by increasing the hardness of our Aluminium 5083 Slatting Coils, by specifying an alloy by means of greater carbon content (without increasing hardness), or by both. These Aluminium 5086 Perforated Coils, which have good mechanical properties both at ambient and elevated temperatures of up to 930 Degree F (500 Degree C), are readily fabricated using common industrial techniques. Low – temperature impact tests (to -50 Degree F) in our Aluminium Steel 5052 Plates are useful for many applications as toughness indicators under various service conditions and temperatures.


Aluminium Coils Specifications

Aluminium Coil Specifications
Specifications : ASTM / ASME SB209
Size : 1000 mm x 60610 mm, 1220 mm x 2440 mm, 1500 mm x 3000 mm, 60610 mm x 60610 mm, 60610 mm x 4000 mm
Thickness : 0.1mm to 12 mm Thk
Form : Coils, Foils, Rolls, Plain Sheet, Shim Sheet, Strip, Flats, Blank (Circle), Ring (Flange)
Finish : Hot rolled plate (HR), Cold rolled sheet (CR), 2B, 2D, BA NO(8), SATIN (Met with Plastic Coated)
Hardness : Soft, Hard, Half Hard, Quarter Hard, Spring Hard etc.

Stainless Steel Coil Chemical Composition

Alloy %
Si		 %
Mg		 %
Mn		 %
Cu		 %
Fe		 %
Cr		 %
Zn		 %
Ti		 %
Others		 %
Al
EN AW-1050 A 0.25
Max		 0.05
Max		 0.05
Max		 0.05
Max		 0.40
Max		 – 0.07
Max		 0.05
Max		 – 99.5 Min
EN AW-1070 A 0.20
Max		 0.03
Max		 0.03
Max		 0.03
Max		 0.25
Max		 – 0.07
Max		 0.03
Max		 – 99.7 Min
EN AW-1100 Si+Fe 0.95 Max – 0.05 Max 0.05 – 0.20 – – 0.10 Max 0.05 Max – 99.0 Min
EN AW-2011 0.40 Max – – 5.00 – 6.00 0.70 Max – 0.30 Max – Bi : 0.20 – 0.60
Pb : 0.20 – 0.60		 Remainder
EN AW-2014 0.50 – 1.20 0.20 – 0.80 0.40 – 1.20 3.90 – 5.00 0.70 Max 0.10 Max 0.25 Max 0.15 Max – Remainder
EN AW-2024 0.50 Max 1.20 -1.80 0.30 – 0.90 3.80 – 4.90 0.50 Max 0.10 Max 0.25 Max 0.15 Max 0.15 Max Remainder
EN AW-3003 0.60 Max – 1.00 – 1.50 0.05 – 0.20 0.70 Max – 0.10 Max – 0.15 Max Remainder
EN AW-3103 0.50 Max 0.30 Max 0.90 – 1.50 0.10 Max 0.70 Max 0.10 Max 0.20 Max 0.10 Max – Remainder
EN AW-6101A 0.30 – 0.7 0.40 – 0.90 0.03 Max 0.05 Max 0.40 Max – – – 0.10 Max Remainder
EN AW-6005 0.60 – 0.90 0.40 – 0.60 0.10 Max 0.10 Max 0.35 Max 0.10 Max 0.10 Max 0.10 Max – Remainder
EN AW-6351 0.70 – 1.30 0.40 – 0.80 0.40 – 0.80 0.10 Max 0.50 Max – 0.20 Max 0.20 Max 0.15 Max Remainder
EN AW-6060 0.30 – 0.60 0.35 – 0.60 0.10 Max 0.10 Max 0.10 – 0.30 0.05 Max 0.15 Max 0.10 Max – Remainder
EN AW-6061 0.40 – 0.80 0.80 – 1.20 0.15 Max 0.15 – 0.40 0.70 Max 0.04 – 0.35 0.25 Max 0.15 Max – Remainder
EN AW-6063 0.20 – 0.60 0.45 – 0.90 0.10 Max 0.10 Max 0.35 Max 0.10 Max 0.10 Max 0.10 Max – Remainder
EN AW-6082 0.70 – 1.30 0.60 -1.20 0.40 – 1.00 0.10 Max 0.50 Max 0.25 Max 0.20 Max 0.10 Max – Remainder